There are a few ways to remove a Pioneer double-din car stereo without keys. One way is to use a flathead screwdriver to pry the faceplate off. Another way is to insert a thin object, like a credit card, into the space between the faceplate and the body of the stereo and then gently prizing it off.
Finally, if there are screws holding the faceplate on, you can remove them with a Phillips head screwdriver.
- If your Pioneer car stereo is secured with a double din mounting sleeve, you will need to remove the sleeve before you can remove the actual stereo unit
- To do this, insert a flat head screwdriver or other thin tool into the small notch on the bottom edge of the sleeve and pry it off
- Once the sleeve is removed, you should see two screws near the top of the stereo unit that are holding it in place
- Remove these screws with a Phillips head screwdriver and set them aside
- Next, there are four spring clips located around the perimeter of the opening where the stereo sits
- Use a flat head screwdriver or similar tool to release these clips by pushing down on them from above
- With all four clips released, you should be able to pull out the entire stereo unit
Credit: www.youtube.com
FAQ
How Do You Get a Car Stereo Out Without a Key?
If you’re lucky, there will be a slot on the side or back of the stereo that you can insert a flathead screwdriver into and twist. If not, then you’ll need to remove the entire unit from the dash to get to the wires in order to hotwire it.
How Do I Remove My Pioneer Car Stereo?
If you’re looking to remove your Pioneer car stereo, there are a few things you’ll need to do. First, disconnect the negative battery terminal to avoid any electrical shorts. Next, use a panel tool to remove the trim around the stereo.
Once the trim is removed, you’ll be able to access the screws holding the stereo in place. Remove these screws and carefully pull the stereo out of the dash. If your car has an antenna attached to the back of the stereo, be sure to unscrew this as well before completely removing the unit.
With a few simple steps, you can easily remove your Pioneer car stereo!
How Do You Remove a Double Din Radio With Keys?
If you’re looking to remove a double DIN radio from your car, the process is actually fairly simple. All you need is a small flathead screwdriver and a set of keys.First, start by inserting the flathead screwdriver into the slot on the side of the radio.
Apply pressure to the screwdriver until you feel it pop out slightly. This will release the locking mechanism on the side of the radio.Next, use your keys to pry open the front panel of the radio.
There are usually two tabs located at the top of the panel that you can insert your keys into and pull apart. Once the front panel is removed, you should be able to see two screws holding in place. Remove these screws with a Phillips head screwdriver and set them aside.
Now, grab hold of the sides of the double DIN radio and pull it out towards you. It may take a little bit of force, but it should come out relatively easily. And that’s it!
You’ve now successfully removed your double DIN radio without any damage or fuss.
How Do You Take the Faceplate off a Pioneer Radio?
There are a few different ways to take the faceplate off a Pioneer radio. The first way is to use a Phillips head screwdriver. Simply unscrew the two screws that are holding the faceplate in place.
You may need to use a little bit of force, but be careful not to strip the screws. Once the screws are removed, you should be able to gently pull the faceplate off. Another way to remove the faceplate is by using a flathead screwdriver.
Insert the flathead screwdriver into the notch at the bottom of the faceplate and pry it off. Again, be careful not to strip any screws. Once you have removed the faceplate, you will likely see another layer of plastic or metal underneath.
This is called the sub-faceplate and it can also be removed in one of two ways. The first way is by unscrewing two small Phillips head screws that are holding it in place. Once these screws are removed, you should be able to gently pull the sub-faceplate off.
The second way to remove the sub-faceplate is by inserting a thin object (such as a credit card) between the edge of the sub-faceplate and where it meets up with the main body of the radio. Gently pry up on this until you hear/feel a “snap.” Be careful not break anything while doing this step!
After snapping off the sub-face plate, you should now have full access to all of the buttons and knobs on your radio.
The easy way (without keys) to remove an aftermarket (pioneer/kenwood) car radio head unit:
How to Remove Kenwood Double Din Without Keys
If you’re looking to remove your Kenwood double din without the keys, there are a few things you’ll need to do. First, locate the two screws on the side of the unit that hold it in place. Once you’ve found those, unscrew them and pull the unit out from its housing.
Next, find the four screws on the back of the unit that secure it to the dash. Once you’ve removed those, carefully pull the unit out of the dash and disconnect any wiring that’s attached to it. Finally, remove any mounting brackets or clips that are holding the unit in place and then slide it out of its housing.
With a little bit of effort, you should be able to remove your Kenwood double din without any issue!
Conclusion
If you’re looking to remove your Pioneer double din car stereo without any keys, there are a few things you can do. First, if you have the installation manual that came with the stereo, check to see if there are any instructions on how to remove it. If not, you can try using a flat head screwdriver to gently pry the stereo out of its housing.
If that doesn’t work, you may need to take your car to a professional who can remove it for you.