Use a flat head screwdriver to remove the plastic trim around the radio. Unscrew the four bolts that hold the radio in place with a Phillips head screwdriver. Disconnect the wiring harness and antenna from the back of the radio.
Pull the radio out of its housing.
- Unscrew the four bolts that hold the head unit in place with a Phillips head screwdriver
- Disconnect the wires from the back of the head unit
- Pull the head unit out of the dash
- Replace with a new head unit and reattach all wires and screws
Credit: www.amazon.com
FAQ
How Do You Remove a Kenwood Head Unit?
Assuming you want to know how to remove a Kenwood head unit from a car:
1. Disconnect the negative battery cable. This will prevent any shorts while working on the electrical system.
2. Locate the four screws that hold the radio in place, two on each side. Remove these screws with a Phillips screwdriver and pull the radio out of its opening. Unplug all wiring harnesses connected to the back of the radio. These are generally color coded to make it easy to reconnect them later.
3a. For double-DIN radios, there will be two sets of wires plugged into the back of the unit—one for power and one for speakers. Use your multimeter set to “ohms” or “resistance” mode (Ω) to test which wire is which before disconnecting anything. To do this, touch one lead of your multimeter to each wire in turn and check the continuity between them (i.e., whether there is a complete circuit). The power wires will have continuity between them, but not with any of the speaker wires—and vice versa for speaker wires. Once you’ve identified each set of wires, label them or take note of their positions so you can reattach them correctly later.
3b. For single-DIN radios, there is only one set of wires plugged into the back (for both power and speakers). As above, use your multimeter set to “ohms” or “resistance” mode (Ω) to test which wire is which before disconnecting anything. Touch one lead of your multimeter to each wire in turn and check continuity between them (i.e., whether there is a complete circuit). The positive power wire will have continuity with all other positive power wires, but not with any negative ones.
The same goes for negative wires —test for continuity between each individual wire and its corresponding positive counterpart until you find one that doesn’t show continuity. That’s your ground/negative wire—label it or take note of its position so you can reattach it correctly later. With all other wiring sorted, you can now remove your old Kenwood head unit completely!
How Do You Remove a Kenwood Dnx?
If you need to remove your Kenwood DNX head unit, there are a few steps you’ll need to follow. First, disconnect the negative battery terminal to prevent any electrical shorts. Next, remove any trim or panels that may be blocking access to the head unit.
Once you have access, unscrew and remove the faceplate of the head unit. With the faceplate removed, you should be able to see and disconnect all of the wiring harnesses attached to the back of the unit. Finally, remove the mounting screws holding the unit in place and carefully pull it out of the dash.
How Do You Remove a Dual Stereo?
Assuming you would like tips on how to remove a dual stereo from your car:First, disconnect the negative battery cable to prevent any electrical shorts. Next, use a panel tool or flat head screwdriver to pry off the trim panels surrounding the stereo.
Once the panels are removed, unscrew any bolts holding the stereo in place. You may need to disconnect additional wiring harnesses before completely removing the stereo. Finally, reinstall in reverse order and test before driving!
How Do You Remove a Kenwood Faceplate?
Assuming you need to remove the faceplate from your Kenwood car stereo, there are a few things you’ll need. First, you’ll need a small screwdriver or a pick. You’ll also need something to prop up the faceplate so you can see what you’re doing – a stack of books or a box will do.
Finally, you’ll need patience and good eyesight!The first step is to locate the four tiny screws that hold the faceplate onto the main unit. These are usually located in the corners of the faceplate, but may be hidden behind rubber plugs.
Once you’ve found all four screws, remove them and carefully set them aside.Next, gently pry up on one side of the faceplate with your screwdriver or pick. It should pop off easily, but be careful not to damage any of the plastic tabs that hold it in place.
If it’s being stubborn, try moving around to another corner and popping it off from there.Once the faceplate is off, take a look at all the connections between it and the main unit. There should only be two – one for power and one for audio output.
If there are more than two, consult your car stereo’s manual for assistance (or bring it into a professional if you’re unsure).To remove the power connector, simply unplug it from both ends – there should only be one way it will fit back together again. For an audio output connector (like for an aux input), gently push down on one side while pulling up on the other until it comes free from both sides.
Again, consult your manual if you’re having trouble here.With both connectors disconnected, you should now be able to completely remove your Kenwood faceplate without any issue!
$50 Double Din Review and Removal (HD MP5)
How to Remove Kenwood Double Din Without Keys
Removing a Kenwood double din without the keys can be a bit tricky. However, with a few simple tools and some patience, it can be done relatively easily. Here are the steps:
1) Use a flat head screwdriver to remove the two screws that hold the top of the double din in place. These screws are located at the very top of the unit, just below where the buttons are located.
2) Once the screws have been removed, gently pull up on the top of the double din unit. This will release the clips that hold it in place. Be careful not to damage these clips, as they will need to be reused when reinstalling the unit.
3) With the top of the unit released, you should now be able to see four bolts holding down each corner of the double din. Remove these bolts using an appropriate-sized socket wrench or ratchet.
4) With all four bolts removed, you should now be able to gently pull out the entire double din unit from its housing. If it is stuck, simply wiggle it back and forth until it comes free.
Conclusion
Kenwood is a well-known electronics company that produces a wide range of products, including car stereo head units. If you own a Kenwood double din head unit and want to remove it, there are a few things you need to know. First, disconnect the power and ground wires from the back of the unit.
Next, remove the four screws that hold the unit in place. Finally, carefully pull the unit out of its mounting bracket. With these steps, you’ll be able to quickly and easily remove your Kenwood double din head unit.