If your Ram pickup truck didn’t come with a backup camera installed from the factory, you can easily add one yourself. You’ll just need to purchase a backup camera kit specific for Ram trucks and follow the instructions that come with it. In most cases, you’ll need to run a power wire from the battery to the camera location and connect the video cable from the camera to the display screen.
Once everything is wired up, you can test it out by putting your truck in reverse.
- Park your Ram Pickup in a well-lit area and turn off the engine
- Locate the backup camera mounting location on the rear of the vehicle
- This will be somewhere near the center of the vehicle, just below the roofline
- Clean the surface around the mounting location with a clean cloth to remove any dirt or debris
- Affix the backup camera to the mounting location using the screws that come with it
- Do not overtighten as this could damage the camera housing
- 5 Connect one end of the power cable to the backup camera and route it along the underside ofthe vehicle towardsthe front
- Look for an unused grommet in one ofthe body panels through which you can feedthe cable
- If there is no unused grommet, carefully drill a hole large enoughto accommodatethe power cableand seal it with silicone caulkto prevent leaks
- Feedthe power cable throught he grommet or hole and into thee engine compartment
- 6 Locate thee reverse light wire inthe engine compartment(this will be white witha black tracer)and spliceintoit usinga quick connectorf T-tap connector
- 7 Connectothe other endof thee powercabletoethe reverse light wire (now tappedinto),then tuckall excesswiringaway so it isn’t hanging loose underyour vehicle whereit could get damagedor caughton something while you’re driving
Dodge Ram 1500 Reverse Camera Installation Guide
If you’re looking to install a reverse camera in your Dodge Ram 1500, this guide will show you how. First, you’ll need to purchase a reverse camera. We recommend the Rear View Safety RVS-770613N back-up camera, which is specifically designed for the Ram 1500.
Once you have your camera, begin by opening the tailgate and removing the two screws that secure the license plate light housing. Then, remove the four bolts that hold the spare tire carrier in place. With those removed, you can now lower the carrier enough to access the wiring harnesses.
Locate the black/red wire coming from the left taillight assembly. This is your power wire. Use a circuit tester or multimeter to verify that it has 12 volts of DC power when the ignition is turned on.
If not, check your fuse box for a blown fuse (the Ram 1500’s backup cameras are protected by fuse number 28 in the Totally Integrated Power Module).Now find the blue/white wire coming from the right taillight assembly. This is your ground wire.
Use a circuit tester or multimeter to verify that it has continuity with a known good ground point on your vehicle (you can use one of the bolts holding down the spare tire carrier as a ground point).With both wires verified, use butt connectors to splice them into your reverse camera’s power and ground wires respectively. Then route thecamera’s video cable through one ofthe openings in th ecarrierand towardsthe front ofthevehicle untilit reachesyour head unit .
Dependingon what kindofhead unityouhave(factoryor aftermarket), thereare different ways to connectthevideo cabletoit so thatyoucanviewthereverseimageon its display screenwheninreversegear . Finally , once everythingisconnectedproperly , replace allofther earpanelscrews , reinstallthesparetirecarrierandlicenseplatelighthousing , andtestoutyournewreverse camerabyputtingitinto reversegear!
Credit: brakelightcamera.com
Can You Add Backup Camera to Dodge Ram?
If you’re looking to add a backup camera to your Dodge Ram, there are a few things you’ll need to take into account. First, you’ll need to decide which type of backup camera system you want. There are wired and wireless options available, and each has its own set of pros and cons.
Wired backup cameras typically offer better image quality than wireless ones, but they can be more difficult to install. Wireless cameras are much easier to install, but they may not provide the same level of image quality as their wired counterparts.Once you’ve decided on the type of backup camera system you want, you’ll need to choose a location for it.
The best place for a backup camera is usually on the back of the vehicle, near the license plate. You’ll also need to make sure that the camera is mounted in a way that allows it to see behind the vehicle when it’s in reverse.Once you’ve chosen a location and installed thecamera, you’ll needto connect itto your vehicle’s electrical system.
This can be done by splicing into the reversing light wiring or by running a new wire from the battery directly to the camera. If you’re not comfortable doing this yourself, there are kits available that will make installation much easier.
Can You Add a Backup Camera to Uconnect?
If you’re looking to add a backup camera to your Uconnect system, there are a few things you’ll need to do. First, check and see if your Uconnect system is compatible with a backup camera. If it is, then you’ll need to purchase the appropriate camera and install it.
Here’s a quick guide on how to do that:1. Purchase a backup camera that’s compatible with your Uconnect system. You can find these online or at most electronics stores.
2. Install the backup camera in your vehicle according to the instructions that come with it. This will usually involve mounting the camera somewhere on the back of your car and connecting it to power.3. Once the camera is installed, open up the Uconnect settings menu and select “Backup Camera.”
This will allow you to enable and disable the feature as well as calibrate the image so it appears correctly on your screen.
How Much Does It Cost to Install a Backup Camera in a Ram 1500?
Adding a backup camera to your Ram 1500 is a great way to improve safety and visibility when backing up. Installation costs will vary depending on the type of camera you choose and where you have it installed. Expect to pay between $100 and $200 for most aftermarket backup cameras, plus additional labor costs if you have it professionally installed.
Can I Add a Backup Camera to My Truck?
Adding a backup camera to your truck can give you an extra set of eyes when reversing, and can help you avoid obstacles and potential hazards. If you’re considering installing a backup camera on your truck, there are a few things to keep in mind.First, you’ll need to choose the right location for the camera.
It’s important to place the camera high enough that you’ll be able to see clearly behind your vehicle, but not so high that it’s obstructed by your rear window or roofline. You’ll also want to make sure the camera is positioned centrally, so that you have a good view of both sides of your truck bed.Once you’ve decided on the perfect location for your backup camera, it’s time to start installation.
If you’re comfortable working with electrical wiring, then installing the camera yourself shouldn’t be too difficult. However, if you’re not confident in your ability to wire up the camera correctly, it’s best to leave this task to a professional installer.Overall, adding a backup camera to your truck can be a great way to improve safety while reversing.
Just be sure to take care when choosing the location for the camera, and hire a professional installer if necessary.
2013-2017 Ram Truck Backup Rear Camera Upgrade – Easy Plug & Play Install!
Conclusion
If your Ram pickup didn’t come with a backup camera installed, you can easily add one yourself. You’ll just need to purchase a backup camera kit and wire it into your truck’s electrical system. The most difficult part of the installation will be running the wiring from the camera to the truck’s electrical system, but if you take your time and follow a few simple steps, you should be able to do it without any problems.
Once the wiring is in place, all you’ll need to do is mount the camera and connect it to the power source.