Yes, you can add a backup camera to a Jeep. You will need to purchase a backup camera kit and then follow the instructions that come with the kit to install the camera.
- Park your Jeep in a well-lit area and set the parking brake
- Pop the hood and disconnect the negative battery terminal to avoid any electrical shorts while working on your Jeep
- Locate the factory taillight wires near the rear of your Jeep
- You will need to tap into these wires for your backup camera to work correctly
- Use wire taps or splice into the factory taillight wires and connect them to the positive and negative leads on your backup camera according to the manufacturer’s instructions
- Route the backup camera wire up to the front of your Jeep, being careful not to route it too close to any moving parts or hot engine components
- Once you have routed the wire to the front of your Jeep, connect it to the input on your aftermarket head unit or navigation system that is designated for a backup camera signal
How to Activate Backup Camera on Jeep
If you have a Jeep with a backup camera, you may be wondering how to activate it. Here’s a quick guide on how to do just that:
1. Locate the backup camera button on your Jeep’s dash. This is typically located near the stereo or infotainment system.
2. Press and hold the backup camera button for a few seconds. The camera should turn on and begin displaying the view behind your Jeep.
3. To exit the backup camera view, press the same button again or select another option on your Jeep’s dash.
Credit: oembackupcam.com
FAQ
Can You Add a Backup Camera to a Jeep?
If you’re looking to add a backup camera to your Jeep, there are a few things you’ll need to take into account before making your purchase. First, you’ll need to decide what type of camera system you want. There are many different types on the market, from simple and inexpensive cameras that just mount on your rear bumper, to more complex systems that integrate with your Jeep’s infotainment system.
Once you’ve decided on the type of camera system you want, you’ll need to make sure it’s compatible with your Jeep. Some camera systems will only work with certain models or years, so it’s important to do your research before making a purchase. Once you’ve found a compatible backup camera system for your Jeep, installation is relatively straightforward.
Most systems come with all the necessary hardware and instructions for installation. However, if you’re not comfortable doing the installation yourself, there are many qualified professionals who can do it for you. Adding a backup camera to your Jeep can be a great addition if you frequently find yourself driving in reverse or in tight spaces.
It can give you an extra level of safety and peace of mind knowing that you have an extra set of eyes watching out for obstacles behind you.
How Much Does It Cost to Install a Backup Camera in a Jeep Wrangler?
Backup cameras are a great addition to any vehicle, and they can be especially useful in a Jeep Wrangler. Here’s what you need to know about installing a backup camera in your Wrangler.The cost of a backup camera itself will vary depending on the make and model of the camera, but you can expect to pay anywhere from $100 to $300 for a good quality camera.
If you’re looking to have the camera professionally installed, that will add another $100 or so to the total cost.So, all told, you’re looking at around $200 to $400 for a backup camera in your Jeep Wrangler. That may seem like a lot, but it’s actually not bad considering the peace of mind and added safety that a backup camera can provide.
Can You Install a Backup Camera in a Jeep Wrangler?
Installing a backup camera in a Jeep Wrangler is a popular aftermarket modification. Although there are many different ways to go about this, we will show you one way that is relatively simple and does not require any special tools. First, remove the two bolts holding the spare tire carrier in place using a wrench or socket.
Next, unclip the electrical connector for the taillight. Now you will need to remove the entire taillight assembly by removing the three screws holding it in place. Once the taillight is removed, locate the hole for the backup camera mount and drill a pilot hole using a 1/8” bit.
Install the backup camera into the mount and reattach your taillight assembly. Reconnect your electrical connector and then bolt your spare tire carrier back into place. That’s it!
You now have a functional backup camera on your Jeep Wrangler.
How Much Does It Cost to Add a Backup Camera?
Adding a backup camera to your vehicle can be a great safety feature, and it can also be a lot of fun. But how much does it cost to add a backup camera? The answer depends on the type of backup camera you choose, as well as the make and model of your vehicle.
A basic rear-view camera system can start at around $100, while more advanced systems with features like night vision and front-view cameras can cost upwards of $1,000. If you’re looking to add a backup camera to your car, there are a few things to keep in mind. First, you’ll need to decide what type of system you want.
Do you want a simple rear-view camera, or do you want something more advanced with features like night vision and front-view cameras? Second, you’ll need to take into account the make and model of your vehicle when choosing a system. Some cars will require special mounts or brackets in order for the camera to fit properly, so it’s important to choose one that’s compatible with your car.
Finally, think about how much you’re willing to spend on this addition. Backup cameras can range in price from around $100 for a basic system up top$1,000 for more advanced models with all the bells and whistles.
2007 – 2017 Jeep Wrangler Backup Camera Install
Conclusion
If you own a Jeep and are wondering if you can add a backup camera, the answer is yes! There are many aftermarket products available that will allow you to do this, and it is relatively simple to install. A backup camera can be a great addition to your Jeep, as it can help improve safety when reversing.